NPort® 5100 device servers were developed to make serial devices network-compatible in no time at all. Due to their small size, the servers are ideal for
connecting devices such as card readers and payment terminals to an IP-based Ethernet LAN. Use the NPort 5100 device servers to give your PC
software direct access to serial devices from anywhere on the network.

Most cost-effective serial-to-Ethernet solution
The use of serial device servers to connect legacy serial devices to Ethernet is commonplace today, and users expect device servers to be cost-effective
and offer a wide range of useful features. With full support for Microsoft and Linux operating systems, the NPort® 5100 Series is the best choice for serial-to-Ethernet converters.

Adjustable termination and pull high/low resistors
In some critical environments, termination resistors may be required to prevent reflection of serial signals. When using terminating resistors, it is
also important to set the pull high/low resistors correctly so that the electrical signal is not distorted. Since there is no set of resistor values that is universally
compatible with all environments, the NPort® 5100 device servers are supplied with jumpers that can be used to set the termination and pull high/low resistor values for
each serial port.

Standard TCP/IP interface and wide choice of operating modes
The NPort® 5100 device servers can be configured for TCP server, TCP client, UDP server/client, pair connection or Ethernet modem mode,
ensuring compatibility with software based on a standard network API (e.g. Winsock or BSD sockets), Winsock or BSD sockets).

Real COM/TTY drivers for existing software
The Real COM/TTY drivers supplied with the NPort® 5100 device servers allow you to continue using software designed to communicate
via COM/TTY ports. Installation and configuration is straightforward and enables seamless communication between your serial devices and your PC over a TCP/
IP network. Using Moxa’s Real COM/TTY drivers is a great way to protect your software investment while realising the
benefits of networking your serial devices.

Easy troubleshooting
NPort® 5100 device servers support SNMP, which allows all devices to be monitored over Ethernet. Each device can be configured to automatically send trap messages
to the SNMP manager when user-defined errors occur. For users who do not use the SNMP manager, an e-mail warning
can be sent instead. Users can define the trigger for the alerts using Moxa’s Windows utility or the web console. For example, warning messages
can be triggered by a warm start, a cold start or a password change.

Specifications

Ethernet interface
– 10/100BaseT(X) ports (RJ45 connector) 1
– Magnetic isolation protection 1.5 kV (built-in)

Ethernet Software functions
– Configuration options Web console (HTTP), serial console (NPort 5110/5110-T/5150 only), Telnet console,
– Windows utility
– Management DHCP client, IPv4, SNTP, SMTP, SNMPv1, Telnet, DNS, HTTP, ARP, BOOTP, UDP,
– TCP/IP, ICMP
– Windows Real COM driver Windows 95/98/ME/NT/2000, Windows XP/2003/Vista/2008/7/8/8.1/10 (x86/x64),
– Windows 2008 R2/2012/2012 R2 (x64), Windows Embedded CE 5.0/6.0, Windows XP
– Embedded
– Linux Real TTY Drivers Kernel versions: 2.4.x, 2.6.x, 3.x, 4.x and 5.x
– Fixed TTY Drivers SCO UNIX, SCO OpenServer, UnixWare 7, QNX 4.25, QNX 6, Solaris 10, FreeBSD, AIX 5.
– x, HP-UX 11i, Mac OS X
– Android API Android 3.1.x and higher
– MIB RFC1213, RFC1317

Serial interface
– Connector DB9 male
– Number of ports 1
– Serial standards: NPort 5150: RS-232, RS-422, RS-485
– Operating modes Disabled, Ethernet Modem, Pair connection, Real COM, Reverse Telnet, TCP Client,
– TCP Server, UDP
– Baud rate: NPort 5150: 50 bps to 921.6 kbps
– Data bits 5, 6, 7, 8
– Stop bits 1, 1.5, 2
– Parity None, Even, Odd, Space, Mark
– Flow control RTS/CTS (RS-232 only), DTR/DSR (RS-232 only), XON/XOFF
– Pull High/Low resistance for RS-485 NPort 5130/5150: 1 kilo-ohm, 150 kilo-ohm
– RS-485 data direction control NPort 5130/5150: ADDC® (automatic data direction control)

Serial signals
– RS-232 TxD, RxD, RTS, CTS, DTR, DSR, DCD, GND
– RS-422 Tx+, Tx-, Rx+, Rx-, GND
– RS-485-4w Tx+, Tx-, Rx+, Rx-, GND
– RS-485-2w Data+, Data-, GND

Power parameters
– Input current: NPort 5130/5150: 200 mA @ 12 VDC
– Input voltage 12 to 48 VDC
– Qty. of current inputs 1
– Source of input power Current input socket

Physical characteristics
– Metal housing
Dimensions (with ears) 75.2 x 80 x 22 mm (2.96 x 3.15 x 0.87 in)
Dimensions (without ears) 52 x 80 x 22 mm (2.05 x 3.15 x 0.87 in)
– Weight 340 g (0.75 lb)
– Installation Desktop mounting, DIN rail mounting (with optional kit), wall mounting

Environmental limits
– Operating temperature Standard models: 0 to 55°C (32 to 131°F)
– Wide range temp. Models: -40 to 75°C (-40 to 167°F)
– Storage temperature (including packaging) -40 to 75°C (-40 to 167°F)
– Relative humidity 5 to 95% (non-condensing)

Standards and certifications
– EMC EN 55032/24
– EMI CISPR 32, FCC Part 15B Class A
– EMS IEC 61000-4-2 ESD: Contact: 4 kV; Air: 8 kV
IEC 61000-4-3 RS: 80 MHz to 1 GHz: 3 V/m
IEC 61000-4-4 EFT: Power: 1 kV; Signal: 1 kV
IEC 61000-4-5 Surge: Power: 1 kV
IEC 61000-4-6 CS: 150 kHz to 80 MHz: 3 V/m; Signal: 3 V/m
IEC 61000-4-8 PFMF
IEC 61000-4-11 DIPs
– Safety UL 60950-1

MTBF
– Time NPort: NPort 5150: 2.736,202 hrs
– Standards Telcordia (Bellcore) Standard TR/SR

Package contents
– Device 1 x NPort 5100 Series Device Server
– Power supply 1 x Power supply, suitable for your region (all models except NPort 5110-T)
– Documentation 1 x Quick installation guide