A single door mechanism that enables complete entry and exit control via connected access readers.

Overview
– Dimensions: 174.9 x 126 x 32.9 mm (6.9 x 5 x 1.3″)
– Supported doors: 1
– Input terminals: (2) Door exit request (1) Door position (1) Emergency
– Power supply method: PoE++ UL 294 Power-limited Class 2 PSU UL 60950-1/62368-1 LPS/PS2 PSU

Mechanical
– Weight: 363 g (12.8 oz)
– Housing material: Polycarbonate
– Mounting material: Polycarbonate
– Mounting: DIN rail (included)

Hardware
– Indoor and outdoor use: indoor use only
– Operating temperature: 0 to 40° C (32 to 104° F)
– Operating humidity: 5 to 95% non-condensing
– Network interface: (5) 10/100/1000 Base-T
– PoE interface: (1) PoE++ input, 50V DC, 1A (4) PoE outputs, 50V DC, 15.4W per port (Max. 28W aggregated)
– Max. Power consumption: 30 W (without PoE output) 50 W (with PoE output)
– Digital input: Request to leave, request to enter, remote unlock, door position sensor
– Dry output relay
Interlock: 30V DC, 1A
Aux: 30V DC, 1A
– Powered output relay
Interlock: 12V DC, 1A
Aux: 12V DC, 0.33A
12V DC, 0.33A
– LEDs: W/B
– Buttons: (1) Factory reset
-Recommended max. cable length Max. cable length
UA-Lock-Electric (400mA): 24 AWG Length: 25 m (82 ft) 22 AWG Length: 42 m (138 ft) 20 AWG Length: 66 m (217 ft) 18 UACC-Cable-DoorLockRelay Length: 100 m (328 ft)
UA-Lock-Magnetic-540kg (500mA): 24 AWG Length: 20 m (66 ft) 22 AWG Length: 32 m (105 ft) 20 AWG Length: 51 m (167 ft) 18 UACC-Cable-DoorLockRelay Length: 80 m (262 ft)
UA-Lock-Magnetic-270kg (800mA): 24 AWG Length: 12 m (29 ft) 22 AWG Length: 20 m (98 ft) 20 AWG Length: 30 m (167 ft) 18 UACC-Cable-DoorLockRelay Length: 46 m (151 ft)
– Other Locks (1A): 24 AWG Length: 9 m (30 ft) 22 AWG Length: 15 m (49 ft) 20 AWG Length: 24 m (79 ft) 18 UACC-Cable-DoorLockRelay Length: 36 m (118 ft)
– PoE Cabling Requirements: Cat 5e cabling is recommended as the minimum power category. The power category used should match the transmission speed required at the installation site. The minimum allowable conductor cross-section for the connection between the PSE or Power Injector and the PD is 26 AWG (0.13 mm² ) for patch cords; 24 AWG (0.21 mm² ) for horizontal or riser cables.
– UL 294 Statement: Compliance with IEEE 802.3 (at or af) specifications has not been verified under UL 294. The device is intended to comply with the section of the National Electrical Code, ANSI/NFPA 70, Article 725.121, Power Sources for Class 2 and Class 3 Circuits.
– CAN/ULC-60839-11-1 Class: Classification: 1
– Certifications: CE, FCC, IC, UL 294, CAN/ULC-60839-11-1
– Document number and issue date and/or revision level: UA-Hub-Door002, V01

Software
– Management application: Access
– Software information: The software version can be checked at https://unifi.ui.com.