OTD140 - Outdoor router, 2 x ETH ports, 4G mobile radio module (LTE)

MOBILE
- Cellular module 4G (LTE) - LTE Cat 4 150 Mbps DL, 50 Mbps UL; 3G - 21 Mbps DL, 5.76 Mbps UL; 2G - 236.8 kbps DL, 236.8 kbps UL
- SIM switch 2 SIM cards, auto-switch cases: Weak signal, data limit, SMS limit, roaming, no network, network denied, data connection error, SIM idle protection
- Status
IMSI, ICCID, operator, operator status, data connection status, network type, bandwidth, connected band, signal strength (RSSI), SINR, RSRP, RSRQ, EC/IO, RSCP, sent/received data, LAC, TAC, cell ID, ARFCN, UARFCN, EARFCN, MCC and MNC
- SMS
SMS status, SMS configuration, sending/reading SMS via HTTP POST/GET, EMAIL to SMS, SMS to EMAIL, SMS to HTTP, SMS to SMS, scheduled SMS, SMS autoreply, SMPP
- USSD Supports sending and reading of Unstructured Supplementary Service Data messages
- Black/White list Operator Black/White list (by country or individual operator)
- Band management Band lock, Band status display
- APN Auto APN
- Bridge Direct connection (bridge) between mobile ISP and device in the LAN
- Passthrough Router assigns its mobile WAN IP address to another device in the LAN

ETHERNET
- LAN 2 x ETH ports (can be configured as WAN), 10/100 Mbps, compliance with IEEE 802.3, IEEE 802.3u, 802.3az standards, supports Auto MDI/MDIX Crossover

POE IN
- PoE Ports 1 x PoE In
- PoE Standards 802.3af/at

POE OUT
- PoE Ports 1 x PoE Out
- PoE Standards 802.3af Alternative B
- PoE Max Power per Port (at PSE) 15 W Max (power supply dependent)

NETWORK
- Routing Static routing, dynamic routing (BGP, OSPF v2, RIP v1/v2, EIGRP, NHRP), policy based routing
- Network protocols
TCP, UDP, IPv4, IPv6, ICMP, NTP, DNS, HTTP, HTTPS, SFTP, FTP, SMTP, SSL/TLS, ARP, VRRP, PPP, PPPoE, UPNP, SSH, DHCP, Telnet, SMPP, SNMP, MQTT, Wake On Lan (WOL)
- VoIP passthrough support H.323 and SIP-alg protocol NAT helpers that enable correct routing of VoIP packets
Connection monitoring
Ping Reboot, Wget Reboot, Periodic Reboot, LCP and ICMP for link inspection
- Firewall Port forwarding, traffic rules, user-defined rules
- Firewall status page
Display all firewall statistics, rules and rule counters
- Ports management Display the device ports, activate and deactivate the individual ports, switch the automatic configuration on or off, change the transmission speed, etc.
- Network topology Visual representation of your network showing which devices are connected to which other devices
- DHCP Static and dynamic IP assignment, DHCP relay
- QoS / Smart Queue Management (SQM) Traffic priority queuing by source/destination, service, protocol or port, WMM, 802.11e
- DDNS Supported >25 service providers, others can be configured manually
- Network backup VRRP, wired options, any of which can be used as automatic failover
- Hotspot
Captive portal (hotspot), internal/external radius server, SMS authorisation, internal/external landing page, walled garden, user scripts, URL parameters, user groups, individual user or group restrictions, user management, 9 default customisable themes and the ability to upload and download custom hotspot themes
- SSHFS Ability to mount a remote file system via the SSH protocol

SECURITY
- Authentication Pre-shared key, digital certificates, X.509 certificates, TACACS+, Radius, block IP & login attempts
- Firewall Pre-configured firewall rules can be activated via WebUI, unlimited firewall configuration via CLI; DMZ; NAT; NAT-T
- Attack prevention
DDOS prevention (SYN flood protection, SSH attack prevention, HTTP/HTTPS attack prevention), port scan prevention (SYN-FIN, SYN-RST, X-mas, NULL flags, FIN scan attacks)
- VLAN Port and tag-based VLAN separation
- Mobile quota control Mobile data limit, customisable time period, start time, warning limit, telephone number
- WEB filter Blacklist for blocking unwanted websites, whitelist for specifying only permitted sites
- Access control Flexible access control from SSH, Web interface, CLI and Telnet

VPN
- OpenVPN Multiple clients and a server can run simultaneously, 27 encryption methods
- OpenVPN encryption
DES-CBC 64, RC2-CBC 128, DES-EDE-CBC 128, DES-EDE3-CBC 192, DESX-CBC 192,
BF-CBC 128, RC2-40-CBC 40, CAST5-CBC 128, RC2-64-CBC 64, AES-128-CBC 128, AES-128-CFB 128, AES-128-CFB1 128, AES-128-CFB8 128, AES-128-OFB 128, AES-128-GCM 128, AES-192-CFB 192, AES-192-CFB1 192, AES-192-CFB8 192, AES-192-OFB 192, AES-192-CBC 192, AES-192-GCM 192, AES-256-GCM 256, AES-256-CFB 256, AES-256-CFB1 256, AES-256-CFB8 256, AES-256-OFB 256, AES-256-CBC 256
- IPsec
IKEv1, IKEv2, with 14 encryption methods for IPsec (3DES, DES, AES128, AES192, AES256, AES128GCM8, AES192GCM8, AES256GCM8, AES128GCM12, AES192GCM12, AES256GCM12, AES128GCM16, AES192GCM16, AES256GCM16)
- GRE GRE tunnels, GRE tunnels over IPsec support
- PPTP, L2TP client/server instances can run simultaneously, L2TPv3, L2TP over IPsec support
- Stunnel proxy designed to add TLS encryption functionality to existing clients and servers, without changing the programme code
- DMVPN
Method for building scalable IPsec VPNs
- SSTP SSTP client instance support
- ZeroTier ZeroTier VPN client support
- WireGuard WireGuard VPN client and server support
- Tinc Tinc provides encryption, authentication and compression in its tunnels. Client and server support.

OPC UA
- Supported modes Client, Server
- Supported connection types TCP

MODBUS
- Supported modes Server, Client
- Supported connection types TCP
- User defined registers
MODBUS TCP user defined register block requests that can be read/written to a file within the router and used to extend MODBUS TCP client functionality
- Supported data formats 8-bit: INT, UINT; 16-bit: INT, UINT (MSB or LSB first); 32-bit: float, INT, UINT (ABCD (big-endian), DCBA (little-endian), CDAB, BADC), HEX, ASCII

DATATO SERVER
- Protocol HTTP(S), MQTT, Azure MQTT
- Data to server Extract parameters from multiple sources and different protocols,

MODBUS MQTT GATEWAY
- Modbus MQTT Gateway Enables sending commands and receiving data from MODBUS server through MQTT Broker

DNP3
- Supported modes Station, Outstation
- Supported connections TCP

DLMS
- DLMS Support DLMS - Standard protocol for exchanging meter data

API
- Teltonika Networks Web API (beta) Support
Extend the capabilities of your device by using a range of configurable API endpoints to retrieve or modify data. For more information, please read this documentation: https://developers.teltonika-networks.com

MONITORING & MANAGEMENT
- WEB UI HTTP/HTTPS, status, configuration, FW update, CLI, troubleshooting, event log, system log, kernel log
- FOTA firmware update from server, automatic notification
- SSH SSH (v1, v2)
- Email Receive email status messages for various services
- SMS SMS status, SMS configuration, send/read SMS via HTTP POST/GET
- Calls restart, status, mobile data on/off, outbox on/off, answer/hang up with timer
- TR-069 OpenACS, EasyCwmp, ACSLite, tGem, LibreACS, GenieACS, FreeACS, LibCWMP, Friendly tech, AVSystem
- MQTT MQTT Broker, MQTT Publisher
- SNMP SNMP (v1, v2, v3), SNMP Trap
- JSON-RPC Management API via HTTP/HTTPS
- RMS Teltonika Remote Management System (RMS)

IOTPLATFORMS
- Cloud of Things Enables the monitoring of: Device data, mobile data, network information, availability
- ThingWorx Enables monitoring of: WAN type, WAN IP, mobile provider name, mobile network signal strength, mobile network type
- Cumulocity Enables monitoring of: Device model, revision and serial number, WAN type and IP, cellular cell ID, ICCID, IMEI, connection type, carrier, signal strength
- Azure IoT Hub
Can send device IP, number of bytes sent/received, temperature, PIN count to Azure IoTHub server, mobile connection status, network connection status, IMEI, ICCID, model, manufacturer, Series, revision, IMSI, SIM status, PIN status, GSM signal, WCDMA RSCP, WCDMA EC/IO, LTE RSRP, LTE SINR, LTE RSRQ, CELL ID, operator, operator number, Connection type

SYSTEM CHARACTERISTICS
- CPU Mediatek, 580 MHz, MIPS 24KEc
- RAM 128 MB
- FLASH memory 16 MB

FIRMWARE/ CONFIGURATION
- WEB UI Update FW from file, check FW on server, configuration profiles, configuration backup
- Update FOTA FW
- Update RMS FW/configuration for multiple devices simultaneously
- Retain settings Update FW without losing the current configuration

FIRMWARECUSTOMISATION
- Operating system RutOS (OpenWrt based Linux OS)
- Supported languages Busybox Shell, Lua, C, C++ and Python, Java in package manager
- Development tools SDK package with provided build environment
- GPL customisation
You can create your own custom firmware and website application by changing colours, logos and other elements in our firmware to suit your needs or those of your customers.

POWER
- Plug RJ45 socket
- Input voltage range 42.5-57.0 VDC, reverse polarity protection, overvoltage/transient protection
- Input voltage range for PoE 42.5-57.0 VDC, reverse polarity protection, overvoltage/transient protection
- Power consumption Idle: < 2.5 W / Max: < 6 W / PoE Max < 21 W

PHYSICAL INTERFACES
- Ethernet 2 x RJ45 ports, 10/100 Mbps
- Status LEDs 3 x mobile connection type, 3 x mobile connection strength, 4 x ETH status LEDs
- SIM 2 x SIM slots (Mini SIM - 2FF), 1.8 V/3 V
- Power RJ45, PoE In, 42.5 - 57.0 VDC
- Antennas 2 x internal antennas
- Antenna specifications
1 x 698 - 960 / 1710 - 2690MHz, 50 Ω, VSWR <3.5, gain <3 dBi, omnidirectional
1 x 698 - 960 / 1710 - 2690MHz, 50 Ω, VSWR <3, gain <4.5 dBi, omnidirectional
- Reset Reboot/User default reset/Factory reset button

PHYSICAL SPECIFICATIONS
- Housing material plastic (PC+ASA)
- Dimensions (W x H x D) 110 x 49.30 x 235 mm
- Weight 855 g
- Mounting options Mounting bracket (for vertical flat surface or pole mounting)

OPERATING ENVIRONMENT
- Operating temperature -40 °C to 75 °C
- Operating humidity 10 % to 90 % non-condensing
- Protection class IP55

REGULATORY & TYPE CERTIFICATIONS
- Regulations CE, UKCA, EAC, UCRF, RCM