DS20U3 V2 - XPC slim DS20U3V2

Fanless and quiet
- Passive cooling, no fan noise
- Ideal for noise-sensitive environments
- Less contamination from dust - therefore virtually maintenance-free

Low power consumption
- Power loss when idle with 2.5" SSD under Windows 10: only approx. 6 W

24/7 continuous operation
- This device is officially approved for 24-hour continuous operation (24/7).
- Prerequisites Free air circulation around the PC Freely accessible ventilation holes on the device. Requirements:
Free air circulation in the vicinity of the PC
Freely accessible ventilation holes on the device.
If a hard disk is installed, this must also be approved by the manufacturer for 24/7 operation.

Housing
- Slim PC (nettop) with black steel housing
- Without fan, complete with passive cooling
- The installation bays for memory, 2.5" drive and M.2 cards are easily accessible behind two covers.cards are easily accessible behind two cover plates
- Dimensions: 20 x 16.5 x 3.95 cm (LWH) = 1.3 litres
- Weight: 1.5 kg net and 2.2 kg gross
- Two openings for Kensington Lock and numerous
- M3 threaded openings on both sides of the housing.

Operating position:
1) Vertical: The device is usually operated in an upright position using the supplied stand (DisplayPort connection facing upwards).
2) VESA mount: Use the supplied VESA mount to install the device behind a suitable monitor, for example.
Note: Operation in a horizontal position is permitted from a thermal point of view, but there are no rubber feet on the device. The maximum operating temperature is then 35 °C.

Operating system
- This barebone system is supplied without an operating system.
- It is compatible with Windows 10/11 (64-bit) and Linux (64-bit).

Processor
- Model: Intel Core i3-10110U (ULV)
- System-on-a-chip architecture (SoC) with integrated memory and graphics controller
- FCBGA1528 package - soldered directly onto the mainboard
- Codename: Comet-Lake-U (10th generation Intel Core) - Core: Intel Core-10110U (ULV) - Codename: Comet-Lake-U (10th generation Intel Core) - Core: Intel Core-10110U (ULV). Generation Intel Core)
- Cores / Threads: 2 / 4
- Base clock speed: 2.1 GHz
- Max. Turbo clock rate: 4.1 GHz
- Intel Smart Cache: 4 MB
- Power dissipation (TDP): max. 15 W
- Manufacturing process: 14nm
- Maximum junction temperature: 100 °C
- Supports 64-bit, VT-x (EPT), VT-d, Enhanced SpeedStep, NX-Bit, AES-NI, SSE 4.1/4.2

Integrated graphics
- Intel UHD Graphics
- Graphics clock frequency: 300-1000 MHz
- Execution units (EUs): 23
- Supports DirectX 12, OpenGL 4.5
- Supports H264, H265 8/10-bit, VP8/9, VC-1, AVC hardware decoding
- Supports Quick Sync Video and Clear Video HD technology
- Supports up to three independent displays:
1) DisplayPort 1.2 supports Ultra HD @ 60 Hz
2) HDMI 2.0a supports Ultra HD @ 60 Hz
3) D-Sub/VGA supports analogue displays

Mainboard / BIOS
- Shuttle Mainboard FS20
- High-quality solid capacitors
- Supports resume after power failure [6]
- Supports Wake on LAN (WOL)
- Supports power on by RTC Alarm
- Supports booting from M.2SSD cards and USB devices
- AMI BIOS in 16 MByte EEPROM with SPI interface
- Supports hardware monitoring and watchdog function
- Supports the Unified Extensible Firmware Interface (UEFI)
- Supports firmware TPM (fTPM) version 2.0

Power supply
- External 65 W power supply (fanless)
- Input: 100-240 V AC, 50/60 Hz, max. 1.6 A
- Output: 19 V DC, max. 3.42 A, max. 65 W
- Length of DC cable: approx. 170 cm
- Length of AC mains cable: approx. 170 cm (3-pin with C6 cloverleaf and Schuko plug)

DC input
- DC plug: 5.5 / 2.5 mm (outer/inner diameter)
- The DC input of the computer supports a
- external power supply with 12V±5% and 19V±5%.

Memory support
- 2x SO-DIMM slot with 260 pins
- Supports DDR4-2666 (PC4-21300) SDRAM with 1.2 V
- Also supports DDR4-3200, but with 2666 MHz
- Supports dual-channel mode
- Supports maximum 32 GB per slot
- Total capacity maximum 64 GB
- Supports unbuffered DIMM modules (no ECC or registered)

2,5" drive bay with SATA connection
- Supports one Serial ATA hard drive
or one SATA SSD drive in 6.35 cm / 2.5" format
- Drive height max. 12.5 mm
- Supports Serial ATA III, 6 Gb/s (600 MB/s) data transfer rate
- Supports the Unified Extensible Firmware Interface (UEFI)
- Note: A SATA cable is not required.

M.2Slot for SSDs
- The M.2 2280 BM slot offers the following interfaces:
PCI-Express Gen. 3.0 x4
SATA v3.0 (max. 6 Gbit/s)
- The M.2 plug-in cards used must be 22 mm wide and can have a length of 42, 60 or 80 mm (type 2242, 2260, 2280).
- Supports M.2 SATASSDs. Supports M.2 SATA SSDs (with B+M key) and M.2 PCIe SSDs (with M key)
- Supplied thermal pad for cooling M.2 SSDs.

M.2-2230E slot for WLAN cards
- Interfaces: PCI-Express Gen. 2.0 X1 and USB 2.0
- M.2-2230 usedplug-in cards used must be 22 mm wide and 30 mm long (type 2230)
- Supports WLAN expansion cards (Optional Shuttle accessories: WLN-M / WLN-M1)
- 2x pre-installed antenna cable

Cardreader
- Integrated SD card reader for reading and writing
- from SD, SDHC and SDXC flash memory cards

Sound function
- Audio Realtek® ALC897 or ALC662 High-Definition Audio
- Two analogue 3.5 mm audio connectors on the front:
1) 2-channel line-out (headphones)
2) Microphone input
- Digital multi-channel audio output via HDMI and DisplayPort

Dual network (2.5G + 1G)
- Two RJ45 network connections
- Network chips used:
1) left: Intel i225 Ethernet controller supports 2,500 / 1,000 / 100 MBit/s data transfer rate
2) right: Intel i219 Ethernet controller supports 1.000 / 100 / 10 MBit/s data transfer rate
- Supports WAKE ON LAN (WOL)
- Supports booting from the network via Preboot eXecution Environment (PXE)

Prepared for wireless network (WLAN)
- 2x pre-installed antenna cable (WLAN card and antennas not included)
- Prepared for the installation of an M.2-2242 WLAN card and two external antennas

Ports/buttons on the front
- 2x USB 3.2 Gen 2 (red, max. 10 Gbit/s)
- 4x USB 2.0
- SD card reader (supports SD, SDHC, SDXC)
- Microphone input
- Audio line-out (headphones)
- On/off button
- Power indicator LED (blue)
- Hard drive LED (yellow)

Rear connections
- DisplayPort 1.2 [3]
- HDMI 2.0a
- D-Sub/VGA
- 2x USB 3.2 Gen 2 (Red, max. 10 Gbit/s)
- 2x Intel RJ45 network (left: 2.5 Gbit/s and right: 1 Gbit/s)
- Serial COM port (5V / 12V, switchable: RS232 / RS422 / RS485) [1]
- DC input for external power supply
- Four-pin connector (2.54 mm pitch) for power button, Clear CMOS and 5 V DC [4]
- Always-on jumper
- If you remove jumper J9 (see quick guide), the PC will start unconditionally as soon as the power supply is established. [6]

Scope of delivery
- Multilingual installation guide
- Two metal feet with four M3 x 7 mm screws
- VESA bracket for 75/100 mm standard (two metal brackets)
- Four M3 x 7 mm screws (connects VESA bracket to PC)
- Four M4 x 10 mm screws (connects VESA bracket to external mounting)
- Two M3 x 5 mm screws for mounting a 2,5" drive
- Two M3 x 5 mm screws for mounting M.2-cards
- Heat conduction pad for cooling M.2SSDs
- Driver DVD for Windows
- External 65W power supply unit with power cable (with earthing contact)

Optional accessories
- PCP11: Adapter cable for a second COM port (replaces the VGA port)
- CXP01: Adapter cable for an external power button
- WWN03: LTE adapter kit for the 2.5" bay with two external LTE antennas [2]
- WLN-M / WLN-M1: WLAN module (supports WLAN/Bluetooth) with two external antennas and cables
- PRM01: 2U rack panel for two Shuttle XPC slim
- DIR01: DIN rail mounting kit (for 35 mm DIN rails)

Environmental parameters
- Permissible operating temperature range: 0-40 °C [5]
- Relative humidity, non-condensing: 10-90 %

Conformity and certificates
- EMI: CE, FCC, BSMI, RCM, VCCI
- Safety: CB, BSMI, cTUVus
- Other: RoHS, Energy Star, ErP
- This device is categorised as Class B information technology equipment (ITE) and is primarily intended for use in residential and office environments. The CE mark confirms conformity with the following EU directives:
(1) Directive 2014/30/EU on electromagnetic compatibility (EMC)
(2) Directive 2014/35/EU on the safety of electrical equipment (LVD)
(3) Directive 2009/125/EC on the ecodesign of energy-related products (ErP)

Notes:
[1] Jumper for COM port configuration:
Pin 9 of the two COM ports is a multifunctional connection. The mainboard jumper JP1 can be used to configure whether pin 9 is switched as a "Ring
Indicator" (RI) or provides an external power supply of
5 V or 12 V. Both COM ports can be configured individually.
The COM 1 connection can be set to either RS232, RS422 or RS485 in the BIOS setup.
The second COM port (COM 2) only supports RS232 mode. The connection is only available on the mainboard in the standard configuration of this product. To route this interface to the outside as a D-Sub connection, you need the appropriate adapter (e.g. the optional accessory PCP11) and you have to do without the VGA connection.

[2] LTE adapter kit WWN03
By using the LTE adapter kit WWN03, the 2.5" bay can no longer be used for SATA drives in 2.5" format (hard disk or SSD); instead, an SSD card in M.2-2280 format must be used as mass storage.format must be used as mass storage instead.

[3] Convert DisplayPort to HDMI/DVI
The DisplayPort output can be converted to HDMI or DVI using an inexpensive, passive adapter cable. For example:
DELOCK 82590: 1m, DisplayPort (male, 20P) to HDMI-A (male, 19P)
DELOCK 82435: 5m, DisplayPort (male, 20P) to DVI-D (male., 24P)
The integrated graphics function recognises the characteristics of the connected display and outputs the appropriate electrical signal - either DisplayPort (without adapter) or HDMI/DVI (with adapter).
Conversely, a monitor with DisplayPort cannot be connected to the HDMI output via a simple, passive adapter.

[4] Four-pin connector on the rear
This enables the connection of an external power button.
In addition, a 5 V DC voltage is provided for external components and the CMOS memory can be cleared using a jumper (Clear CMOS). A suitable cable is available as optional accessory CXP01.

[5] Attention: For high ambient temperatures from 35 °C, it is recommended to use SSDs instead of hard disks.

[6] Automatic switch-on after power failure:
In the BIOS setup under "Power Management Configuration" there is the function "Power-on after Power Fail", which defines how the PC reacts after a power failure. In principle, however, this function can fail in the event of very short power failures, meaning that this product also has a pure hardware solution. If jumper J9 is removed (see quick guide), the PC will start as soon as the power supply is restored.